background image

Security Door Controls

801 Avenida Acaso, Camarillo, Ca. 93012  •   (805) 494-0622  •  Fax: (805) 494-8861
www.sdcsecurity.com  •  E-mail: [email protected]

The E4KP EntryCheck™ is a fully self-contained proximity access control reader.  It is keypad programmable and 
does not require software or a PC connection.

INSTALLATION/PROGRAMMING INSTRUCTIONS

E4KP ENTRYCHECK

P:\INSTALLATION INST\Access Controls\INST-E4KP\INST-E4KP.vsd     Rev C      10-09     Page 1

Features

HID compatible Proximity Reader
Up to 3" read range with ProxCard II
Weather resistant reader enclosure
Memory capacity stores up to 650 user cards
Cost-effective solution for access control and 
personnel management
Access mode selectable

1. Proximity card only
2. Proximity card + PIN

Master code for programming functions
Main password function

Security password function
Forced entry alarm
Door prop alarm
Duress output
User card can be registered/deleted in single

or batch mode (with consecutive numbers)

Reader Lockout activated when the wrong card is

presented more than five times

Lock and alarm output relays programmable

1-99 seconds or on-off latching

Separate remotely located relay module for

for higher security

Optional Cards & Key Fobs

Part# 

HID1326-10 

– (10) Prox Cards, HID ProxCard II

Part# 

HID1346-10 

– (10) Prox Key Fobs, HID ProxKey II

HID ProxCard®  II & ProxKey®  II are registered trademarks of HID Corporation

Summary of Contents for E4KP ENTRYCHECK







Reviews: