KEYPAD –
MODEL E4KP
CONTROLLER RELAY MODULE –
MODEL E5RM
+12V
GND
CLOCK
DATA
+
-
ACCESS
CONTROLLER
K3 FUNCTION SETTING
FUNCTION
DURESS/SHUNT
GUARD
PATROL
1
2
3
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
MODEL : E5RM
S/N : 12345678
K3
ALARM
STRIKE
DOOR SENSOR
EXIT BUTTON
INPUT DC12V
ON
1 2 3
PROGRAMMING OPTIONS (CONTINUED)
SPECIFICATIONS
Keypad – Model E4KP
Operating Voltage:
10V – 15V DC
Power Consumption:
120mA Max @ 12VDC
Frequency
:
125KHz
Read Range
:
Up to 3" (Card, In noise-free environment)
Keyboard
:
12 Keys (0~9, , #), Membrane Keys
Indicator
:
Dual Color LED (Green/Red)
Memory (User) Capacity
:
670 Cardholders
Card Format
:
HID Compatible 125KHz
Cable Length
:
1 Ft.
Dimensions
:
3" W x 4-3/8" H x 0.9" D (75 x 112 x 23 mm)
Weight
:
8.5 ounces
Operating Temperature
:
32
o
F – 122
o
F (0
o
C – 50
o
C)
Humidity
:
30% ~ 95% (Non-condensing)
Controller Relay Module – Model E5RM
Operating Voltage:
10V – 15V DC
Power Consumption:
300mA Max @ 12VDC (with E4KP)
Relay
:
Strike: 5A N.O. / 3A N.C. @ 30VDC
Alarm/Aux.: 1A @ 30VDC
Inputs
:
Exit Button (N.O.)
Door Status Sensor (N.O. or N.C)
Dimensions
:
1-3/4" W x 2-5/8" L x 0.9" D (46 x 66 x 21 mm)
Weight
:
2.5 ounces
Operating Temperature
:
32
o
F – 122
o
F (0
o
C – 50
o
C)
Humidity
:
30% ~ 95% (Non-condensing)
*
Change Default Passwords
Enter Programming Mode
{Alternating Red & Green LED}
To change System Setup Password (Default = 111111),
Press + New 6-digit Pa #
{Alternating Red & Green LED}
To change Door Open Password (Default = 1234)
,
Press + New 4-digit Pa #
{Alternating Red & Green LED}
To change Patrol Password (Default = 1234567)
Press + New 7-digit Pa #
{Alternating Red & Green LED}
Press # to exit Programming
{Solid Red LED}
Enable Patrol Function (Default = Patrol Function Disabled)
With this feature enabled, entering the Patrol Password will send a 1 second pulse on the Auxiliary (K3) Relay:
Enter Programming Mode
{Alternating Red & Green LED}
Press 831 + # (enables Patrol Function, use 830 + #)
{Alternating Red & Green LED}
Press # to exit Programming
{Solid Red LED}
NOTE
: DIP SWITCH 3 on the E5RM control module, must be ON.
*
*
*
P:\INSTALLATION INST\Access Controls\INST-E4KP\INST-E4KP.vsd Rev C 10-09 Page 5
Change a User’s PIN (
Entry Mode 2 Only
)
Press + 2 + # + Present Card OR (Enter Card #)
{Flashing Red LED}
Enter old 4-digit PIN + #
{Flashing Red LED}
Enter new 4-digit PIN + #
{Solid Red LED}
NOTE
: It is NOT required to enter Programming Mode to change a PIN.
Clear Memory / Reset to Default Settings
Enter Programming Mode
{Alternating Red & Green LED}
Press 99 #
{Green LED will flash rapidly, then Alternating Red & Green LED}
Press # to exit Programming
{Solid Red LED}
*
