Command groups
Table 2-40: Trigger commands (cont.)
Command
Description
TRIGger:{A|B}:LOGICPattern:
{CH<x>|CH<x>_D<x>}
Sets or queries the Logic Pattern that is used along with the De
fi
ne Logic choice to
determine when the logic trigger occurs.
TRIGger:{A|B}:LOWerthreshold:CH<x>
Sets or queries CH<x> lower trigger level.
TRIGger:{A|B}:PULSEWidth:
LOGICQUALi
Sets whether or not to use logic quali
fi
cation for a pulse width trigger.
TRIGger:{A|B}:PULSEWidth:HIGHLimit
Speci
fi
es the upper limit to use, in seconds, when triggering on detection of a pulse
whose duration is inside or outside a range of two values.
TRIGger:{A|B}:PULSEWidth:LOWLimit
Speci
fi
es the lower limit to use, in seconds, when triggering on detection of a pulse
whose duration is inside or outside a range of two values.
TRIGger:{A|B}:PULSEWidth:POLarity
Speci
fi
es the polarity for a pulse width trigger.
TRIGger:{A|B}:PULSEWidth:SOUrce
Speci
fi
es the source waveform for a pulse width trigger.
Speci
fi
es to trigger when a pulse is detected with a width (duration) that is less than,
greater than, equal to, or unequal to a speci
fi
ed value.
Speci
fi
es whether or not to use logic quali
fi
cation for a runt trigger.
Speci
fi
es the polarity for the runt trigger.
Speci
fi
es the source waveform for the runt trigger.
Speci
fi
es the type of pulse width the trigger checks for when it detects a runt.
Speci
fi
es the width, in seconds, for a runt trigger.
TRIGger:{A|B}:SETHold:CLOCk:EDGE
Speci
fi
es the clock edge polarity for setup and hold triggering.
TRIGger:{A|B}:SETHold:CLOCk:SOUrce
Speci
fi
es the clock source for the setup and hold triggering.
TRIGger:{A|B}:SETHold:HOLDTime
Speci
fi
es the hold time for setup and hold violation triggering.
Speci
fi
es the setup time for setup and hold violation triggering.
TRIGger:{A|B}:SETHOLDLogicval:
{CH<x>|CH<x>_D<x>}
Sets or queries whether the speci
fi
ed channel is included (INCLude) or not included
(DONTInclude) in the Setup & Hold trigger input con
fi
guration.
TRIGger:{A|B}:TIMEOut:
LOGICQUALi
Speci
fi
es whether or not to use logic quali
fi
cation for a timeout trigger.
TRIGger:{A|B}:TIMEOut:POLarity
When triggering using the
TIMEOut
trigger type, this commands speci
fi
es the
polarity to be used.
When triggering using the
TIMEOut
trigger type, this command speci
fi
es the source.
When triggering using the
TIMEOut
trigger type, this command speci
fi
es the
timeout time, in seconds.
TRIGger:{A|B}:TRANsition:DELTatime
Speci
fi
es the delta time used in calculating the transition value for the transition
trigger.
TRIGger:{A|B}:TRANsition:POLarity
Speci
fi
es the polarity for the transition trigger.
TRIGger:{A|B}:TRANsition:SOUrce
Speci
fi
es the source for a transition trigger.
Speci
fi
es whether to check for a transitioning signal that is faster or slower than
the speci
fi
ed delta time.
TRIGger:{A|B}:TRANsition:
LOGICQUALi
Speci
fi
es whether or not to use logic quali
fi
cation for a transition trigger.
Sets or queries the type of A or B trigger.
MSO54, MSO56, MSO58, MSO58LP Programmer
2-83
Summary of Contents for MSO54
