Tektronix MSO54, Programmer'S Manual

Page: 94 / 1026

Command groups
Table 2-40: Trigger commands (cont.)
Command
Description
TRIGger:{A|B}:BUS:B<x>:ETHERnet:DATa:
SIZe When the Ethernet trigger condition is set to
DATa
, this command speci fi es the
number of contiguous TCP/IPv4/MAC client data bytes to trigger on.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:DATa:
VALue When the Ethernet trigger condition is set to
DATa
, and the quali fi er is set
to
LESSthan, MOREthan, EQual, UNEQual, LESSEQual
or
MOREEQual
, this command speci fi es the value to trigger on.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
IPHeader:DESTinationaddr:VALue When the Ethernet trigger condition is set to
IPHeader
, this command speci fi es
the value of the 32–bit destination address that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
IPHeader:PROTOcol:VALue When the Ethernet trigger condition is set to
IPHeader
, this command speci fi es
the value of the 8–bit protocol fi eld that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
IPHeader:SOUrceaddr:VALue When the Ethernet trigger condition is set to
IPHeader
, this command speci fi es
the value of the 32-bit source address that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:MAC:
ADDRess:DESTination:VALue When the Ethernet trigger condition is set to
MACADDress
, this command speci fi es
the 48–bit MAC destination address that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:MAC:
ADDRess:SOUrce:VALue When the Ethernet trigger condition is set to
MACADDress
, this command speci fi es
the 48–bit MAC source address value that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:MAC:
LENgth:HIVALue When the Ethernet trigger condition is set to
MACLENgth
, and the quali fi er is set to
INrange
or
OUTrange
, this command speci fi es the upper data value of the range.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:MAC:
LENgth:VALue When the Ethernet trigger condition is set to
MACLENgth
, and the quali fi er
is set to
LESSthan, MOREthan, EQual, UNEQual, LESSEQual
or
MOREEQual,
this command speci fi es the 16–bit value to trigger on.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:QTAG:
VALue When the Ethernet trigger condition is set to
QTAG
, this command speci fi es the
32-bit Q-Tag value to trigger on.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
TCPHeader:ACKnum:VALue When the Ethernet trigger condition is set to
TCPHeader
, this command speci fi es
the 32–bit acknowledgement number that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
TCPHeader:DESTinationport:VALue When the Ethernet trigger condition is set
TCPHeader
, this command speci fi es the
16–bit destination port address value that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
TCPHeader:SEQnum:VALue When the Ethernet trigger condition is set to
TCPHeader
, this command speci fi es
the 32–bit sequence number that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:ETHERnet:
TCPHeader:SOUrceport:VALue When the Ethernet trigger condition is set to
TCPHeader
, this command speci fi es
the 16–bit source port address that is to be used in the trigger.
TRIGger:{A|B}:BUS:B<x>:FLEXray:
CONDition Speci fi es the condition to use when triggering on a FlexRay bus signal (start of
frame, frame type, ID, cycle count, header, data, ID and data, EOF, error).
TRIGger:{A|B}:BUS:B<x>:FLEXray:
CYCLEcount:HIVALue Speci fi es the high value when triggering on a FlexRay bus cycle count fi eld.
TRIGger:{A|B}:BUS:B<x>:FLEXray:
CYCLEcount:QUALi
fi er
Speci fi es the quali fi er (<, >, =, <=, >=, ≠ , in range, out of range) to use when
triggering on the FlexRay bus cycle count fi eld.
TRIGger:{A|B}:BUS:B<x>:FLEXray:
CYCLEcount:VALue Speci fi es the low value when triggering on the FlexRay bus cycle count fi eld.
TRIGger:{A|B}:BUS:B<x>:FLEXray:DATa:
HIVALue Speci fi es the high value when triggering on the FlexRay bus data fi eld.
TRIGger:{A|B}:BUS:B<x>:FLEXray:DATa:
OFFSet Speci fi es the offset of the data string, in bytes, when triggering on the FlexRay
bus data fi eld.
2-78 MSO54, MSO56, MSO58, MSO58LP Programmer