![background image](http://html.mh-extra.com/html/tektronix/mso54/mso54_programmers-manual_1078778066.webp)
Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
This command sets or queries the measurement type.
MEASUrement:MEAS<x>:WINDOWLENgth
This command sets or queries the window length for the measurement.
This command sets or queries the global range maximum value.
This command sets or queries the global range minimum value.
Sets or queries the global range state.
This command sets or queries the minimum number of unit intervals required for
BUJ analysis.
MEASUrement:POPUlation:LIMIT:STATE
This command sets or queries the global population limit state.
MEASUrement:POPUlation:LIMIT:VALue
This command sets or queries the global population limit value.
MEASUrement:REFLevels:ABSolute:FALLHigh
Sets or queries the value used as the high reference level of the falling edge.
MEASUrement:REFLevels:ABSolute:FALLLow
Sets or queries the value used as the low reference level of the falling edge.
MEASUrement:REFLevels:ABSolute:FALLMid
Sets or queries the value used as the mid reference level of the falling edge.
MEASUrement:REFLevels:ABSolute:
HYSTeresis
Sets or queries the value of the hysteresis of the reference level.
MEASUrement:REFLevels:ABSolute:RISEHigh
Sets or queries the value used as the high reference level of the rising edge.
MEASUrement:REFLevels:ABSolute:RISELow
Sets or queries the value used as the low reference level of the rising edge.
MEASUrement:REFLevels:ABSolute:RISEMid
Sets or queries the value used as the mid reference level of the rising edge.
MEASUrement:REFLevels:ABSolute:TYPE
Sets or queries the reference level type.
Sets or queries the method used to calculate the TOP and BASE, used to calculate
reference levels.
MEASUrement:REFLevels:JITTERMODE
Sets or queries how often reference levels are calculated on Jitter measurements.
Sets or queries the method used to calculate reference levels.
This command sets or queries how often reference levels are calculated.
MEASUrement:REFLevels:PERCent:FALLHigh
Sets or queries the percentage used to calculate the high reference level of the falling
edge.
MEASUrement:REFLevels:PERCent:FALLLow
Sets or queries the percentage used to calculate the mid reference level of the falling
edge.
MEASUrement:REFLevels:PERCent:FALLMid
Sets or queries the percentage used to calculate the mid reference level of the falling
edge.
MEASUrement:REFLevels:PERCent:
HYSTeresis
Sets or queries the percentage used to calculate the hysteresis of the reference level.
MEASUrement:REFLevels:PERCent:RISEHigh
Sets or queries the percentage used to calculate the high reference level of the rising
edge.
MEASUrement:REFLevels:PERCent:RISELow
Sets or queries the percentage used to calculate the low reference level of the rising
edge.
2-50
MSO54, MSO56, MSO58, MSO58LP Programmer
Summary of Contents for MSO54
