Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
MEASUrement:MEAS<x>:EDGES:
UPPERFREQuency
This command sets or queries the upper frequency for the measurement when the
measurement type is phase noise. Higher frequencies are ignored.
MEASUrement:MEAS<x>:FILTers:
BLANKingtime
This command sets or queries the
fi
lter blanking time for the measurement.
MEASUrement:MEAS<x>:FILTers:GLOBal
This command sets or queries the global
fl
ag for
fi
lter settings for the measurement.
MEASUrement:MEAS<x>:FILTers:HIGHPass:
FREQ
This command sets or queries the high pass
fi
lter frequency for the measurement.
MEASUrement:MEAS<x>:FILTers:HIGHPass:
SPEC
This command sets or queries the high pass
fi
lter order for the measurement.
MEASUrement:MEAS<x>:FILTers:LOWPass:
FREQ
This command sets or queries the low pass
fi
lter cutoff frequency for the measurement.
MEASUrement:MEAS<x>:FILTers:LOWPass:
SPEC
This command sets or queries the low pass
fi
lter order for the measurement.
MEASUrement:MEAS<x>:FILTers:RAMPtime
This command sets or queries the
fi
lter ramp time for the measurement.
This command sets or queries the 'from edge' type for the measurement.
MEASUrement:MEAS<x>:
FROMEDGESEARCHDIRect
This command sets or queries the 'from edge' search direction for the measurement.
This command sets or queries the gating type for the measurement.
MEASUrement:MEAS<x>:GATing:ACTive
This command sets or queries the gating active level when the gating type is logic.
MEASUrement:MEAS<x>:GATing:GLOBal
This command sets or queries the gating settings global
fl
ag.
MEASUrement:MEAS<x>:GATing:HYSTeresis
This command sets or queries the gating hysteresis value when the gating type is
logic.
MEASUrement:MEAS<x>:GATing:
LOGICSource
This command sets or queries the gating data source when the gating type is logic.
MEASUrement:MEAS<x>:GATing:MIDRef
This command sets or queries the gating mid ref value when the gating type is logic.
MEASUrement:MEAS<x>:GATing:
SEARCHSource
This command sets or queries the gating search source when the gating type is
search.
This command sets or queries the reference levels global
fl
ag for the measurement.
MEASUrement:MEAS<x>:HIGHREFVoltage
This command sets or queries the high reference voltage value for the 'time outside
level' measurement.
This command sets or queries the idle time for the measurement when the
measurement type is burst width.
MEASUrement:MEAS<x>:JITTERSummary:
DCD
This command sets or queries whether DCD is included in the jitter summary for
the measurement.
MEASUrement:MEAS<x>:JITTERSummary:
DDJ
This command sets or queries whether DDJ is included in the jitter summary for
the measurement.
2-46
MSO54, MSO56, MSO58, MSO58LP Programmer
Summary of Contents for MSO54
