![background image](http://html.mh-extra.com/html/tektronix/mso54/mso54_programmers-manual_1078778063.webp)
Command groups
Table 2-31: Measurement commands (cont.)
Command
Description
MEASUrement:MEAS<x>:JITTERSummary:
DJDD
This command sets or queries whether DJ-dd is included in the jitter summary for
the measurement.
MEASUrement:MEAS<x>:JITTERSummary:
EYEWIDTHBER
This command sets or queries whether EyeWidth@BER is included in the jitter
summary for the measurement.
MEASUrement:MEAS<x>:JITTERSummary:
NPJ
This command sets or queries whether NPJ is included in the jitter summary for the
measurement.
MEASUrement:MEAS<x>:JITTERSummary:PJ
This command sets or queries whether PJ is included in the jitter summary for the
measurement.
MEASUrement:MEAS<x>:JITTERSummary:
RJDD
This command sets or queries whether RJ-dd is included in the jitter summary for
the measurement.
MEASUrement:MEAS<x>:JITTERSummary:TIE
This command sets or queries whether TIE is included in the jitter summary for the
measurement.
MEASUrement:MEAS<x>:JITTERSummary:
TJBER
This command sets or queries whether TJ@BER is included in the jitter summary for
the measurement.
This command sets or queries the label for the measurement.
MEASUrement:MEAS<x>:LOWREFVoltage
This command sets or queries the low reference voltage value for the 'time outside
level' measurement.
MEASUrement:MEAS<x>:MEASRange:
GLOBal
This command sets or queries the range settings global
fl
ag for the measurement.
MEASUrement:MEAS<x>:MEASRange:MAX
This command sets or queries the range maximum value for the measurement.
MEASUrement:MEAS<x>:MEASRange:MIN
This command sets or queries the range minimum value for the measurement.
MEASUrement:MEAS<x>:MEASRange:STATE
This command sets or queries the range state for the measurement.
MEASUrement:MEAS<x>:
PATTERNDETECTION
This command sets or queries the pattern detection type for the measurement.
MEASUrement:MEAS<x>:PATTERNLENgth
This command sets or queries the pattern length for the measurement.
MEASUrement:MEAS<x>:PATTERNTYPe
This command sets or queries the pattern type for the measurement.
MEASUrement:MEAS<x>:PERFREQ:EDGE
This command sets or queries the edge type of a Period/Frequency measurement.
This command sets or queries the polarity for the measurement when the
measurement type is burst width.
MEASUrement:MEAS<x>:POPUlation:GLOBal
This command sets or queries the population settings global
fl
ag.
MEASUrement:MEAS<x>:POPUlation:LIMIT:
STATE
This command sets or queries the population limit state for the measurement.
MEASUrement:MEAS<x>:POPUlation:LIMIT:
VALue
This command sets or queries the population limit value for the measurement.
MEASUrement:MEAS<x>:REFLevels:
ABSolute:FALLHigh
This command sets or queries the value used as the high reference level of the falling
edge when the measurement's ref level method is set to absolute.
MSO54, MSO56, MSO58, MSO58LP Programmer
2-47
Summary of Contents for MSO54
