manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 96

INSTRUMENT PANEL

5-16

1. Fuel filter
2. Priming pump
3. Water separator
4. Drain plug
5. Connector

A. Opening direction of drain plug

B. Closing direction of drain plug

1. Locate the fuel filter ( ) & water separator ( ) in engine

compartment.

2. Place the water container under the fuel filter & water

separator.

3. Disconnect the connector under the drain plug ( ) of the

water separator.

4. Turn two drain plugs to “ ” direction to drain the water.

5. Press priming pump until all water is drained. After draining,

turn the drain plug until the gasket contact to the threaded
plug hole, then tighten (“ ” direction) it 1/2 turns by hand.

6. Engage the connector under the drain plug and press the

priming pump ( ) until it becomes rigid.

7. Close the engine hood and start the engine.

Be careful not to be injured by surrounding equipment during the
working procedures.

CAUTION

If the priming pump is not properly operated, air may get into the fuel
line. It may cause starting problem or fuel system problem. Make sure
to perform the job in step 6.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands