manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 94

INSTRUMENT PANEL

5-14

HOW TO DRAIN THE WATER FROM FUEL FILTER (EU)

1. Locate the fuel filter ( ) in engine compartment

and place the water container under it.

2. Disconnect the connector ( ) under the drain plug

( ) of the water separator.

3. Turn the drain plug ( ) to “ ” direction to drain

the water.

4. Press priming pump until all water is drained. Af-

ter draining, turn the drain plug until the gasket
contact to the threaded plug hole, then tighten
(“ ” direction) it 1/2 turns by hand.

5. Engage the connector ( ) under the drain plug and

press the priming pump ( ) until it becomes rigid.

6. Close the engine hood and start the engine.

Be carefule not to be injured by surrounding
equipment during the working procedures.

CAUTION

If the priming pump is not properly operated,
air may get into the fuel line. It may cause
starting problem or fuel system problem.
Make sure to perform the job in step 5.

WARNING

1. Fuel filter

2. Drain plug

3. Connector

4. Priming pump

A. Opening direction

of drain plug

B. Closing direction of

drain plug

DIESEL ONLY

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands