manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 216

IN CASE OF EMERGENCY

12-16

Locations of Towing Hook

Front

Rear

• If you cannot use a professional towing service, get into the dis-

abled vehicle during towing. But, never use this emergency tow-
ing when the electrical system, steering system, and brake sys-
tem are not operative.

• You may allow horizontal direction force apply. The vertical direc-

tion force may cause damage to the vehicle.

• If there are steep hills or sharp turns in your towing, do not use

this method.

• It requires more efforts of turning the steering when the engine is

not running.

• Depress the brake pedal stronger than normal condition when the

engine is not running.

• When your electrical systems operate properly, turn on the haz-

ard warning lamps or turn signal lamps according to the towing
vehicle’s signals.

• Avoid overloaded towing and do not tow the heavier vehicle than

yours.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands