manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 116

TRANSMISSION AND BRAKE SYSTEM

6 - 1 8

Warning Sound When Driving While the Park-
ing Brake is Engaged

If you drive the vehicle without releasing the parking brake,
the brake warning light blinks and buzzer sounds to warn the
driver when the vehicle speed exceeds 10 km/h for more than
2 seconds. When this happens, stop the vehicle immediately
and release the parking brake.

PARKING BRAKE OPERATION

Parking brake pedal

Parking brake
release lever

Brake pedal

Accelera-
tor pedal

Parking Brake Operation

Park at a safe place and depress the parking brake pedal
firmly. When the pedal is depressed, the brake warning light
on the instrument panel comes on.

Parking Brake Release

To release parking brake, pull up the parking brake release
lever.

• Before driving off, be sure to check that the brake warning light is

turned off.

• Driving with parking brake applied could damage rear brake system.

Before driving, fully release the parking brake.

• If the brake warning light doesn’t go out after releasing the park-

ing brake, have the brake system checked by Ssangyong Dealer
or Ssangyong Authorized Service Operation.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands