SSANGYONG RODIUS 2006 Owner'S Manual Download Page 223

Page: 223 / 286

IN CASE OF EMERGENCY

12-23

When the vehicle has a serious problem during
driving

1. Turn on the hazard flasher and move the vehicle off the

traffic to a safe place. Set up the warning triangle behind
your vehicle (over 100 m) to warn other vehicles.

2. Have all passengers get out of the vehicle and stay away

from the traffic. When your safety is secured, contact your
Ssangyong dealer for your emergency service.

WARNING TRIANGLE

The warning triangle is
under the fourth row seat.

Check local, state and provincial laws for using the warning triangle.

NOTE

• Move the vehicle off the traffic to a safe place. Turn on the haz-

ard warning lamps and set up the warning triangle behind your
vehicle to warn others.

• Have all passengers get out of vehicle and stand in a safe place.

• At night time, set up a warning lamp behind your vehicle (over

200 m) to warn others.

• On a curved road, provide a emergency hand signal to others at

the point over 200 m behind your vehicle.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands