manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 168

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-12

Auto Button And Temperature Control Switch

When you press Auto button, the "AUTO" indicator is displayed
on the VFD and the temperature of the passenger compartment
is automatically maintained according to the set temperature.
To adjust the temperature and fan speed, turn the switch as
required. When you press Auto button during manual operation
mode, the system is changed to Auto operation mode.

OFF Switch

To stop the air conditioner operation,
press this switch.

Low fan speed

Ambient Temperature Display Button

When you press this button, the "OUTSIDE" indicator appears
and the ambient temperature is displayed on the VFD for
about 5 seconds.

High fan speed

Fan Speed Control Switch

To control the fan speed, turn this switch. When turning this switch in Auto mode,
the “AUTO” indicator goes out and the system is changed to manual mode.

Cool

Hot

If the air conditioner switch is turned off, the air conditioner does not work even when
the fan switch is operated. However, the air flows due to fan operation.

CAUTION

The ambient temperature may not display the actual ambient tem-
perature due to engine heat or ground heat.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands