manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 173

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-17

2. To operate the heater, press "RR HTR" switch. To operate

the air conditioner, press "A/C" switch.

3. When the rear air conditioner switch is at "R" position, the

fan speed can be controlled by this switch.

Hot air

Cool air

4. Hot air flows out from ( ) vent when heating, and cool air

flows out from ( ) vent when cooling.

1. Position the rear air conditioner control switch to any po-

sition except (

) position.

Do not operate the fan for a long time when the engine is not running.
The battery could be discharged.

CAUTION

If the "A/C" switch or "RR HTR" is turned off, the air conditioner does
not work even when the rear air conditioner switch is operated.
However, the air flows due to fan operation.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands