SSANGYONG RODIUS 2006 Owner'S Manual Download Page 122

Page: 122 / 286

SEATS

7-4

DRIVER’S SEAT (POWER SEAT)

Seat Slide Adjustment

Seat Height Adjustment

Seat Tilt Adjustment

Press the button to warm
the seat, and press it again
to stop the operation.

Seat Heater

Seatback Reclining
Adjustment

To raise the head restraint,
pull it up without pressing
the release button. To lower
the head restraint, press the
release button

on top of

seatback and push the head
restraint down.

Seat Warmer Switch

Head Restraint Adjustment

Swing down the lever to increase
the amount of lumbar support. To
decrease it, swing up the lever.

Lumbar Support
(Driver’s Seat Only)

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands