manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 111

TRANSMISSION AND BRAKE SYSTEM

6 - 1 3

In the parking lot as shown in the figure,
the upper portion of the vehicle can be
hit before the sensor operation, so
check with outside rearview mirrors or
by turning your head during parking.

• The parking aid system will not work or improperly work under

following cases:

Certain obstacles that sensors cannot detect

- Wires, ropes, chains.

- Cotton, sponge, clothes, snow that absorb ultrasonic waves.

- Obstacles lower than the bumper.

Not defective but improperly working

- When driving on the rough roads, gravel road, hill and grass.

- When the bumper height is changed due to the heavy load.

- When the sensing portion is frozen.

- When the sensing portion is covered by rain, water drops, snow

or mud.

- When receiving other ultrasonic signals (metal sound or air brak-

ing noises from heavy commercial vehicles).

- When a high-power radio is turned on.

• Do not press or shock the sensors by hitting or high-pressure

water gun while washing, or the sensors will be damaged.

• The parking aid system is just a supplemental device to help your

parking operation. You should continue to utilize the mirrors or turn-
ing your head. Normal precautions when reversing should be
maintained.

CAUTION

        Alarm interval                     Display

no alarm

approx. 2.6 sec

approx. 1.3 sec

alarm stays on

Rearview Display in Multimeter

Alarm interval and display changes
according to the distance:

Distance

over 1.2m

81cm ~ 1.2m

51cm ~ 80cm

below 50cm

Detecting obstacle

at rear right side

Detecting obstacle
at rear center side

Detecting obstacle

at rear left side

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands