manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 204

IN CASE OF EMERGENCY

12-4

If a tyre goes flat, follow the safety instructions as below:

1. Turn on hazard flashers.

2. Move off the road to a safe place away from traffic.

3. Park on a firm and level ground.

4. Change the flat tyre with spare tyre.

CAUTIONS WHEN A TYRE IS FLAT

• Don’t be panic! Improper operation of the steering wheel or abrupt

braking may cause a consequential accident on the road.

• Stop your vehicle to a safe place and turn on the hazard flasher

and then apply the parking brake.

• Stop the engine and set up the warning triangle behind your ve-

hicle (daytime: 100 m, night time: 200 m - on express way).

• Block the front and rear of the wheel diagonally opposite to the

wheel being changed.

• Have all passengers get out of vehicle and stand in a safe place.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands