manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 213

IN CASE OF EMERGENCY

12-13

Engine Check Warning Light

This warning light comes on when the igni-
tion switch is turned to ON and goes out if
the engine is in normal condition. If the light
stays on or comes on while driving, some
of engine control components including
sensors and devices are defective.

Water Separator Warning Light

When the water level inside water separa-
tor in fuel filter exceeds a certain level, this
warning light comes on and buzzer sounds.
If these conditions occur, immediately drain
the water from fuel filter & water separator.

For the draining procedures, please refer to “How to drain the
water from fuel filter” section in this manual.

WATER SEPARATOR WARNING LIGHT AND ENGINE CHECK WARNING LIGHT

When this warning light comes on, the vehicle operates in safety mode
to maintain minimum driving conditions and to prevent the system from
being damaged. In this mode, the engine driving force may be de-
creased or the engine may stall. When this happens, have the sys-
tem checked at the Ssangyong Dealer or Ssangyong Authorized Ser-
vice Operation.

CAUTION

When the water level inside water separator in fuel filter exceeds a
certain level, this warning light comes on and buzzer sounds. Also,
the driving force of the vehicle decreases. If these conditions occur,
immediately drain the water from fuel filter & water separator. If the
above conditions are still existing after draining the water, have the
system checked by Ssangyong Dealer or Ssangyong Authorized Ser-
vice Operation.

CAUTION

• The fuel system in engine may get serious damage if you keep

driving while the warning light is coming on. Prompt correction
should be necessary.

• Before starting the engine, perform the pumping operation of

priming pump until it becomes rigid to fill up the fuel pump with fuel.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands