manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 71

INTERIOR SWITCHES

4 - 2 3

SWITCHES IN OVERHEAD CONSOLE

Sunroof switch

Coupled Operation with Door Remote Control

With the front room lamp coupled switch pressed in, the front
room lamps are turned on for 30 seconds when the doors are
unlocked by the door remote control. The front room lamps
are turned off immediately when closing the door.

Passenger
side

Front Room Lamp
Coupled Switch

Front room lamps (driver’s and
passenger’s) are turned on when
opening one of front doors with
this switch pressed in. The front
room lamps are dimmed out after
closing the door. If this switch is
pressed out, front room lamps are
not turned on even when opening
a front door.

Front Room Lamp Switch

The front room lamps are turned on when pushing the lamp
body regardless of the positions of front room lamp coupled
switch. Press the lamp body again to turn off.

Side Room Lamp Coupled
Switch

Four side room lamps are turned
on when opening a rear door with
this switch pressed in. The side
room lamps are turned off when
closing the door. If this switch is
pressed out, side room lamps are
not turned on even when opening
a rear door.

Side and Rear Room Lamp
Operating Condition

Side and rear room lamps are
turned on only when the side room
lamp coupled switch is pressed in.

Driver side

With the front room lamp coupled switch pressed in, the front room lamps
are turned on when opening a front door regardless of the operation of
front room lamp switch.

NOTE

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands