manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 209

IN CASE OF EMERGENCY

12-9

12. Fit the spare tyre and temporarily tighten the wheel nuts

by hands.

13. Lower the vehicle by rotating the combined wrench

counter-clockwise until the tyre touches the ground.

14. Remove the jack and tighten the wheel nuts securely by

2 or 3 steps in the sequence as shown in the figure.

9. Combine the wheel nut wrench and the jack connection

as shown in figure and hook it into the connecting ring.
Jack up the vehicle by rotating combined wrench clock-
wise until the tyre is off ground about 3 cm.

10. Remove the wheel nuts by hands while the vehicle is

stationary. For rear tyre, release the parking brake
carefully.

11. Remove the tyre and put it under the vehicle body.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands