manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 130

SEATS

7-12

Seatback Reclining Adjustment

Seat Slide Adjustment

Head Restraint Adjustment

THIRD ROW SEAT (9-SEATERS)

To raise the head restraint, pull
it up without pressing the re-
lease button. To lower the head
restraint, press the release
button 

 on top of seatback

and push the head restraint
down.

To change the seatback angle,
lean forward slightly and raise
the lever. Then, lean back to the
desired angle and release the
lever. This lever is designed to
adjust the seatback up to a cer-
tain angle and to make it flat.

To move the seat forward or
backward, pull and hold the
seat slide lever 

 up and

move the seat as required.
Then, release the lever in de-
sired position.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands