manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 154

SEAT BELT AND AIR BAG

8-16

• Do not diagnose the circuit with a circuit tester. Do not

attempt to modify any air bag components including the
steering wheel, air bag mounting area, and harness.

• Do not impact any air bag components including the

steering wheel, air bag mounting area, and harness by
hand or tools. You may get injured by sudden deployment.

• The air bag components will be very hot after deployment.

Do not touch them.

• Once the air bag system is triggered, the triggered air

bag assembly should be removed from the vehicle and
replaced with new one.

• The air bag contains explosive materials, so contact

Ssangyong Dealer or Ssangyong Authorized Service Op-
eration when trashing or replacing it.

• Incorrect air bag inspection can be dangerous and

cause injuries. The air bag system must be disposed
only by Ssangyong Dealer or Ssangyong Authorized Ser-
vice Operation.

• Replace the steering wheel with only Ssangyong genu-

ine part.

• When the engine starts, the air bag warning lamp comes

on for a system check. It goes out after 6 seconds when
the system is normal. If this warning lamp stays ON, then
the system may be defective. Have the air bag system
checked immediately by Ssangyong Dealer or
Ssangyong Authorized Service Operation.

WARNINGS FOR AIR BAG

• The seat belt and air the bags are the most effective

when you are sitting well back and upright in the seat.

• A child restraint system must not be placed on the front

seat. The infant or child can be severely injured by an
air bag inflation in case of an accident.

• Do not carry your child on your lap while driving. You can-

not resist against the impact pressure in an accident.
The child could be crushed between you and the parts
of the vehicle.

• Do not place any objects on the air bag inflation location.

You may get injured by those objects during deployment.

• Do not attach any objects such as a sticker, scent bottle,

or phone holder on the steering wheel pad and to the
dashboard.

• Do not move your seat too close to the steering wheel

or dashboard. If you lower your head, the air bag can hit
your head during inflation and can cause severe injury
or even death.

• Hold only the outer rim of the steering so that the air bag

can inflate without any hindrance.

• Do not place your face or chest near the steering wheel

and dashboard. Also, do not allow anyone to place their
hands, leg or face on the dashboard. The air bag can-
not work properly.

WARNINGS FOR AIR BAG

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands