SSANGYONG RODIUS 2006 Owner'S Manual Download Page 256

Page: 256 / 286

LAMPS

14-2

BULB SPECIFICATIONS AND FUNCTIONAL CHECK

BULB SPECIFICATIONS

FUNCTIONAL CHECK

1. Check whether the lamp comes on or off when its switch

operation.

2. Check the corresponding fuse when the lamp doesn't

come on.

3. If the fuse is blown, replace it with new one. For replacing

procedures, refer to "Fuse Replacement" section in this
manual.

4. If the fuse is not blown, check the bulb and replace it with

new one if needed.

5. If the bulb is not defective, have the system checked by

Ssangyong Dealer or Ssangyong Authorized Service
Operation.

Description

Specification

(EU)

Exterior

lamp

High beam

Low beam

Turn signal lamp

Position lamp

Headlamp

Front fog lamp

Side repeater

55W

27W

8W(27W)

27W

21W

27W

16W

10W

Back-up lamp

Rear fog lamp

License plate lamp

High mounted stop lamp

Front room lamp

Glove box lamp

Door courtesy lamp

Side room lamp

Foot lamp

Rear room lamp

Tail (stop) lamp

Turn signal lamp

General

Interior

lamp

Amount

Rear combina-

tion lamp

• Use only a specified capacity bulb for replacement.

• Disconnect the negative cable on the battery before replacing the

bulb.

• Do not apply excessive force to remove the bulb cover.

• Make sure that the corresponding switch and the ignition switch

are turned off before replacing a bulb.

• Do not touch a bulb with bare hands immediately after turning off

the lamp.

• Do not touch a bulb when it is still illuminating.

• Do not touch a bulb with bare hands. Fingerprint, dust, or mois-

ture stuck to bulb may shorten a bulb life or cause a bulb bursting.
In this case, wipe the bulb glass with a soft cloth.

• Never try to adjust the headlamp aiming by yourself. It should be

done by a qualified technician in Ssangyong Dealer or Ssangyong
Authorized Service Operation.

CAUTION

Specification

(General)

55W

27W

8W(27W)

27W

21W

16W

10W

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands