manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 241

SERVICE AND MAINTENANCE

13-17

BRAKE AND CLUTCH FLUID

Diesel Engine

Gasoline Engine

• The fluid level should be between “MAX” and “MIN” level on

the reservoir.

• If it drops to or below the MIN mark, top up with the speci-

fied fluid. Use only specified fluid.

DOT 4

Service interval

Specification

Change at every 2 years

• Be careful not to enter any foreign materials when adding the fluid.
• Do not add the fluid above "MAX" level.
• Do not allow the fluid to make contact with body paintwork.
• After add the fluid, tighten the cap securely.
• If frequent addition is required, have the system checked by

Ssangyong Dealer or Ssangyong Authorized Service Operation.

CAUTION

• Use only Ssangyong recommended brake fluid.
• Do not allow the fluid to make contact with skin or eyes. If contact

happens, rinse affected areas immediately with plenty of water.
If irritation persists, consult a doctor.

• The fluid gradually decreases according to the wear of the brake

pads. A sudden drop of the fluid level may indicate the leaks in the
system. In this case, have the system checked by Ssangyong
Dealer or Ssangyong Authorized Service Operation.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands