manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 20

SAFETY PRECAUTIONS

1-4

6. Warm up the engine in idling speed. Do not warm up the

engine over 2 minutes.

7. Make sure that there are no persons or obstacles in the

danger area around the vehicle.

8. Release the parking brake.

9.

• Automatic transmission equipped vehicle

Keep the brake pedal depressed and shift into 

“-D+”

position. Make sure that the position indicators of 

“D”

 and

“1”

 are coming. Drive off the vehicle by releasing the brake

pedal slowly.

• Manual transmission equipped vehicle

Keep the brake pedal and clutch pedal depressed and shift
into “1” position. To drive off the vehicle, release the brake
pedal and depress the accelerator pedal gradually while
releasing the clutch pedal slowly.

4.

• Diesel engine equipped vehicle:

Turn the ignition key to “ON” position and check the ap-
propriate warning lights are operating. The preglow indi-
cator light will come on and go out when the glow plugs
are sufficiently heated for cold engine starting. As soon as
the glow indicator goes out, start the engine.

• Gasoline engine equipped vehicle:

Turn the ignition key to “ON” position and check the ap-
propriate warning lights are operating.

5. Crank the engine without touching the accelerator pedal

by turning the igniting key to the “START” position. Release
the key when the engine starts. If the engine starts, but fails
to run, repeat the above procedure.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands