manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 84

INSTRUMENT PANEL

5-4

Coolant Temperature Gauge

The temperature gauge indicates the temperature of engine
coolant when the ignition switch is in the “ON” position.

Fuel Gauge

This gauge indicates the level of fuel
remaining in the fuel tank. Fill up fuel
tank before the needle reaches “E”.

• F : Full

• E : Empty

Tachometer

The tachometer indicates engine speed in revolutions per
minute. Multiply 1,000 to the current number, then it will be
the current number of engine revolutions.

Speedometer

The speedometer indicates the
vehicle speed in kilometers per
hour (km/h).

METER CLUSTER

The engine can overheat.

• If the pointer reaches the red zone, stop the vehicle.

• Allow engine to cool.

CAUTION

Excessive speed can damage engine.

Do not let engine reach excessive speed, indicated by pointer being
in red zone.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands