manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 247

SERVICE AND MAINTENANCE

13-23

WASHER FLUID

Front Washer Fluid Reservoir

Rear Washer Fluid Reservoir

Frequently check the washer fluid level and add the speci-
fied product as needed.

The washer fluid includes flammable materials to prevent freezing. There could be a fire when di-
rectly contacted with flames. When checking the washer fluid, avoid the flames near to washer
fluid tank.

WARNING

• If you use plain water as washer fluid, it will freeze during the winter and damage the washer

fluid reservoir and motor. Use only specified washer fluid.

• Check the washer fluid level before starting to drive.
• Do not operate the wipers when the washer fluid reservoir is empty. It may cause a damage

to the glass when it is dry.

• Do not use radiator antifreeze in windshield washer. It can damage the washer system and

paint.

• If you operate the washer switch without washer fluid, the motor could be damaged due to

overloads. Therefore, if no washer fluid, do not operate the washer motor.

• Fill washer fluid tank only 3/4 full when it is very cold. This allows for expansion, which

could damage the tank if it is completely full.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands