manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 46

OPENING AND CLOSING

3-8

ENGINE HOOD

1. To open the engine hood, pull the release knob   located

on left lower side of instrument panel to unlatch the engine
hood. The engine hood will then be unlocked and partially
opened.

2. Push the safety catch

lever located under the
hood to the arrow direc-
tion 

 and lift up the

engine hood.

• An open engine hood with engine running exposes moving parts

which can crush, cut or entangle.

• Check that the engine hood is fully latched in position by pulling at its

front edge before driving.

• To avoid a personal injury, take care of the separation of the sup-

port rod from the slot especially in windy day.

WARNING

3. To hold the engine hood in the open position, insert the sup-

port rod   into the slot.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands