manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 134

SEATS

7-16

THIRD ROW SEAT (7-SEATERS)

Head Restraint Adjustment

To raise the head restraint,
pull it up without pressing
the release button. To lower
the head restraint, press the
release button   on top of
seatback and push the head
restraint down.

Seat Slide Adjustment

To move the seat forward or backward, pull and hold the seat
slide lever 

 up and move the seat as required. Then, re-

lease the lever in desired position.

Seatback Reclining Adjustment 

To change the seatback angle, lean forward slightly and raise
the lever. Then, lean back to the desired angle and release
the lever. This lever is designed to adjust the seatback up to
a certain angle.

To make the seat sliding adjustment easier, adjust the seat
while passengers are sitting on the seat.

NOTE

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands