manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 218

IN CASE OF EMERGENCY

12-18

Maximum Load Limits

(unit: kg)

In higher elevations the engine output and gradability may drop so
that it may not be possible for the permissible trailer loads to be fully
utilized in mountainous territory.

So, after 1,000m height, permissible trailer loads should be reduced
10% every another 1,000m height.

WARNING

Never exceed the maximum load limits of trailer or trailer towing equip-
ment and be aware that due to the higher load overheating might
occur in hot days or during continuous uphill driving.

WARNING

2WD

4WD

Trailer

2,500

750

2,850

750

Tongue

140

with brake

without brake

with brake

without brake

The above dimensions are certified data to meet the following
conditions.

On a 12% of uphill:

 Capable of 5 starts within 5 minutes

(with trailer)

On a 18% of uphill:

 Capable of 5 starts within 5 minutes

(without trailer)

Type

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands