manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 175

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-19

1. Open the glove box.

Replace the air conditioner filter when

• Unpleasant odor is generated at first operation after long

unused period.

• Cooling and blowing capacity are decreased.

Replace the air conditioner filter at every 10,000 km of driving.
However, if the vehicle is operated under severe conditions
such as dusty road, unpaved road, and excessive air condi-
tioner and heater operation, shorten the replacement interval.

REPLACING AIR CONDITIONER FILTER

2. Remove the glove box from

dash panel by moving both
holders to arrow direction.

3. Remove the filter

cover while push-
ing the holder to
arrow direction.

5. Slightly move the

second filter to
left side and pull
it out.

4. Pull out the first

filter.

Manual

Auto

6. Replace the filters with new ones. Install in the reverse or-

der of removal. Make sure that the filters are facing correct
direction.

Auto

Manual

The arrow should face upward.

The arrow should face downward.

• Do not apply excessive force to the holders when removing the

glove box. It may cause a deformation of holders and results in a
loose installation.

• Replace both air conditioner filters at a time and pay attention to

the installing direction.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands