manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 166

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-10

AUTOMATIC AIR CONDITIONER*

Rear Fan Control
Switch

Sun Sensor

Fault Code Display

This display blinks for about 5 seconds
when the system is defective or the engine
is started.

Air Conditioner Control Panel

Auto Button

Ambient Tem-
perature Sensor

Interior Tempera-
ture and Humidity
Sensor

• If the Auto button is pressed, the temperature of the passenger com-

partment is automatically maintained according to the set temperature.

• By operating the relevant switch of the automatic air conditioner, you can

manually control the air conditioner operation, air flow direction, fan
speed and air source.

• To turn off the air conditioner and heater, press "OFF" button ( 

 ).

• If you use wiper during A/C operation, the air conditioner may be auto-

matically changed to defroster mode according to the wiper operating
conditions (A/C ON, fresh air intake mode).

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands