SSANGYONG RODIUS 2006 Owner'S Manual Download Page 202

Page: 202 / 286

IN CASE OF EMERGENCY

12-2

STARTING THE ENGINE WITH JUMPER CABLES

You can start a vehicle that has a discharged battery by transferring electrical power to it from a battery in
another vehicle.

1. Prepare a set of jumper cable.
2. Apply the parking brake and shift the transmission to

po-

sition (automatic transmission) or neutral (

) position

(manual transmission).

3. If the booster battery is not a MF type battery, remove all vent

plugs from it. Cover the opened vent holes with cloth to avoid
a possibility of battery explosion and other hazards.

Discharged battery

Booster battery

4. Start the engine with the booster battery. Switch off all elec-

trical accessories in the vehicle with discharged battery.

5. Connect one end of the first lead of the jumper cable to the

positive terminal of the discharged battery.

6. Connect other end of this same jumper cable lead to the

positive terminal of the booster battery.

• Connect the positive cable

first when connecting.

• Disconnect the megative

cable first when disconnecting.

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands