SSANGYONG RODIUS 2006 Owner'S Manual Download Page 258

Page: 258 / 286

LAMPS

14-4

HEADLAMP

1. Disconnect the negative cable on the

battery.

2. Disconnect two connectors from the

headlamp.

3. Unscrew three mounting bolts and

remove the headlamp housing from
the vehicle.

4. Remove the cover and bulb from the

headlamp housing.

5. Disconnect the internal connector

and replace the burnt bulb with new
one.

6. Install the headlamp in the reverse

order of removal.

Headlamp

connections

Headlamp

high beam

Headlamp (right side)

Headlamp low

beam

Position lamp

Turn signal lamp

For safety driving, do not adjust the headlamp aiming by
yourself. It should be done by a qualified technician in
Ssangyong Dealer or Ssangyong Authorized Service
Operation.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands