SSANGYONG RODIUS 2006 Owner'S Manual Download Page 37

Page: 37 / 286

IGNITION KEY, REMOTE CONTROL KEY

2-9

OPENING AND CLOSING THE DOORS WITH IGNITION KEY

Door

Locking the door

Unlocking the door

To lock the door:

Turn the key to the lock position (toward
front of the vehicle) from driver’s door or
passenger’s door. All doors except tailgate
will be locked.

To unlock the door:

Turn the key to the unlock position (toward
rear of the vehicle) from driver’s door or
passenger’s door.

All doors except tailgate will be unlocked.

Locking the tailgate

Unlocking the tailgate

Turn the key to the clockwise/coun-
terclockwise direction to lock/un-
lock the tailgate.

Tailgate

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands