manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 128

SEATS

7-10

Seatback Reclining Adjustment

Head Restraint Adjustment

SECOND ROW SEAT (9-SEATERS)

Seat Slide Adjustment

To move the seat forward or
backward, pull and hold the seat
slide lever up and move the seat
as required. Then, release the
lever in desired position.

To change the seatback angle,
lean forward slightly and raise
the lever  . Then, lean back to
the desired angle and release
the lever. This lever is designed
to adjust the seatback up to a
certain angle and to make it flat.

To raise the head restraint, pull it up
without pressing the release button.
To lower the head restraint, press the
release button   on top of seatback
and push the head restraint down.

Seat Under Tray

The seat under trays are located un-
der the seat at both sides. Use the
trays to store some personal properties.

* Locations of cup holder may vary according to the seats.

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands