SSANGYONG RODIUS 2006 Owner'S Manual Download Page 74

Page: 74 / 286

INTERIOR SWITCHES

4 - 2 6

DIRECTION, ATMOSPHERIC PRESSURE, ALTITUDE MODE

Barometer

Altimeter (relative altitude,
absolute altitude)

Speed

sensing

indicator

Press and hold the MODE
button for more than 1
second to switch over the
mode between absolute
altimeter and relative
altimeter.

Increase the altitude in
absolute altimeter

Decrease the altitude in
absolute altimeter

Altimeter

Electronic compass

Speed sensing indicator

Barometer

Electronic

compass

Indication of

relative altimeter

Absolute altimeter

It indicates the current altitude from

sea level (0 m) by every 20 m.

Relative altimeter

It indicates the specific area’s rela-

tive altitude based on the current

altitude of the vehicle.

It indicates 8-direction according to

the vehicle’s driving direction.

The flashing interval of the road

signs changes gradually accord-

ing to the vehicle speed.

It indicates the current atmo-

spheric pressure by 1 hpa.

The indicator stays on below
2.8 km/h of vehicle speed.

NOTE

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands