manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 86

INSTRUMENT PANEL

5-6

Brake Warning Light

When the ignition is switched on, this warn-
ing light comes on and should go out after
4 seconds.

This warning light comes on when the parking brake is ap-
plied and/or the brake fluid level is lower than specified level.

Turn Signal/Hazard Warning
Flasher Indicator

When the turn signal switch is turned
on, this indicator flashes to indicate

operation of the external turn signal. Both right and left
lights flash when the hazard warning switch is turned
on.

Parking

Driving gears

P

R

N

D

1

2

3

4

5

This indicator shows the automatic transmission se-
lector lever position.

When the selector lever is at “D” position while driving,
“D” indicator and currently selected gear indicator are
coming on.

If you move the selector lever to left or right direction,
only the selected gear indicator comes on.

If the vehicle is driven for over 2 seconds (over 10 km/h) while the
parking brake is applied, the parking brake warning light comes on
and warning buzzer sounds. If it occurs, immediately stop the ve-
hicle and release the parking brake.

CAUTION

Driving the vehicle with the brake fluid warning light on is dangerous.
Have the brake system checked and repaired immediately by near-
est Ssangyong Dealer.

WARNING

Reverse

Neutral

Driving

Auto Shift Indicator (for automatic transmission)

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands