manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 79

INTERIOR SWITCHES

4 - 3 1

BATTERY VOLTAGE

BATTERY VOLTAGE

It indicates the current battery voltage by 0.1 V.

When the battery voltage goes below 12.0 V, current display
is changed to battery voltage mode and “LOW VOLTAGE” mes-
sage flashes at every 10 seconds.

Over 12.0 V

(Fully charged)

11.9 ~ 11.0 V

10.9 ~ 10.0 V

9.9 ~ 9.0 V

Battery voltage

Indication

Charging Level

Battery Voltage

• Start the engine and charge the battery voltage when the battery volt-

age is below 12.0 V.

• When starting the engine, the battery voltage is temporarily decreased.

• If the charging level in display is not increased even when the engine

is running, have the system checked at Ssangyong Dealer or
Ssangyong Authorized Service Operation.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands