SSANGYONG RODIUS 2006 Owner'S Manual Download Page 65

Page: 65 / 286

INTERIOR SWITCHES

4 - 1 7

AUDIO REMOTE CONTROL SWITCHES ON STEERING WHEEL*

* The audio system equipped in the vehicle can be controlled by the remote control switches on the steering wheel.

POWER

Audio power on/off when
the button is pressed.

• In radio mode
- Press briefly: Manual searching for a station.
- Press and hold: Automatic searching for a station.

• In CD (DVD) player/Cassette tape mode
- Press briefly: Replay next/previous track.
- Press and hold: Move forward/backward in cur-

rent tract.

MODE

Audio mode changes in
following order:

MUTE

Stops audio output from au-
dio system. To resume the
audio output, press the but-
ton again.

Radio

(FM1 FM2 AM)

Cassette tape

(TV1 TV2)

CD player

(DVD player)

CD changer*

(DVD changer*)

- CD & DVD changer: optional

Increases

volume

VOL

XXXXX

Decreases

volume

SEEK

XXXXX

Summary of Contents for RODIUS 2006































































































































































































































































































Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands

SSANGYONG RODIUS 2006, Owner'S Manual

Search results

Summary of Contents for RODIUS 2006

Reviews:

Brands by name

Popular brands