Home
/
SSANGYONG
/
RODIUS 2006
/
Owner'S Manual

SSANGYONG RODIUS 2006, Owner'S Manual

Share

Page: 41 / 286

SSANGYONG RODIUS 2006 Owner'S Manual Download Page 41

OPENING AND CLOSING

3-3

DOORS

Driver’s Door (Inside)

Automatic Door Locking

All doors will be automatically
locked when you drive over 50 km/h
while the doors are unlocked.

Automatic Door Unlocking

All doors will be automatically unlocked
when the engine is switched off.

Rear Right Door (Inside)

Passenger’s Door (Inside)

The passenger’s door lock/un-
lock button and lever have the
same functions with those of
driver’s door.

The opening levers on the rear
right and rear left door have the
same functions with that of
driver’s door. However, the
lock/unlock button is available
only for the appropriate door.

Rear Left Door (Inside)

Door Lock/Unlock Button

Door Opening Lever

• If you press the door lock/unlock button (A) to the lock (1)

direction, all doors are locked, and vice versa.

• Pull the door opening lever (B) to open the door.

Lock

Unlock

«
...
39
40
41
42
43
...
»

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands