manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 47

OPENING AND CLOSING

3-9

FUEL FILLER DOOR

Open

Close

Fuel Filler Door Release Lever

1. Open the fuel filler door 

by pulling the release lever

 located on left lower side

of driver’s seat.

2. Open the fuel filler cap 

by turning it counterclock-
wise 

.

3. After refueling, tighten

the fuel filler cap by turn-
ing it clockwise 

 and

push the fuel filler door 
properly until it latches.

• Fuel damages paintwork. If fuel spills onto paintwork, immediately

wash the affected area with cold water.

• The fuel filler door may not open in cold weather. Push or tap fuel

filler door lightly to open.

CAUTION

• Gasoline vapor is highly flammable. It burns violently and that can

cause very bad injuries.

• When refueling, • Switch off engine.

• No smoking.

• No naked flame.

• No sparking material.

• Using low quality fuel could result in a serious damage to the engine

due to the water or impurities in fuel. Never use the low quality fuel.

WARNING

Stop the engine before refueling.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands