manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 90

INSTRUMENT PANEL

5-10

Winter Mode Indicator
(For Automatic Transmission)

The indicator comes on when the Win-
ter mode (W) switch near the gear se-
lector lever is presses.

Use this mode to drive off smoothly un-
der icy and slippery road.

Mode switch

Glow Indicator
(For Diesel Engine)

This indicator comes on when the ignition
switch is turned on and stays on for a short

time or may go off right away. The waiting time will vary ac-
cording to the engine coolant temperature. When the glow
plugs are sufficiently heated for cold starting, the light will go
out. Then, the engine should be started.

In the vehicle equipped with direct injection type engine, this
indicator may come on very shortly or may not come on.

Engine Check Warning Light

This warning light comes on when the
ignition switch is turned to ON and
goes out if the engine is in normal

condition. If the light stays on or comes on while driving,
some of engine control components including sensors
and devices are defective.

When the glow indicator comes on while driving or the engine cannot
be started properly, have the glow plug system checked by Ssangyong
Dealer or Ssangyong Authorized Service Operation.

CAUTION

If the engine stops due to complete fuel consumption and then
this light comes on after refueling, the engine’s output power
may be decreased in a certain driving distance (30 km)

CAUTION

When this warning light comes on, the vehicle operates in safety
mode to maintain minimum driving conditions and to prevent the
system from being damaged. In this mode, the engine driving force
may be decreased or the engine may stall. When this happens,
have the system checked at the Ssangyong Dealer or Ssangyong
Authorized Service Operation.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands