manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 27

 SAFETY PRECAUTIONS

1-11

Engine Check Indicator

This warning light comes on when the
ignition switch is turned to ON and goes
out if the engine is in normal condition.

When this warning light comes on, the
engine driving force may be decreased
or the engine may stall in some severe
cases. These are indication of activat-
ing the safety mode to protect engine
system. When this happens, have the
system checked at the Ssangyong
Dealer or Ssangyong Authorized Ser-
vice Operation.

Water Separation Interval

- at every 10,000 km

- when changing the engine oil

Priming Pump Operating
Conditions

1. when completely consumed the fuel

2. after draining the water from the fuel

filter

3. after replacing the fuel filter

- Before starting the engine, perform

the pumping operation of priming
pump until it becomes rigid to fill up
the fuel pump with fuel.

CAUTIONS FOR DIRECT INJECTION TYPE DIESEL ENGINE

Water Separator Warning Light

When the water level inside water
separator in fuel filter exceeds a cer-
tain level, this warning light comes on
and buzzer sounds. Also, the driving
force of the vehicle decreases. If these
conditions occur, immediately drain the
water from fuel filter and water
separator.

For the draining procedures, please
refer to “How to drain the water from
fuel filter” section in this manual.

• When engine check warning light comes on, immediately stop driving and have the engine system checked at Ssangyong Dealer or

Ssangyong Authorized Service Operation.

• Drain the water from fuel filter & water separator immediately after the water separator warning light comes on. The fuel system in engine

may get serious damage if you keep driving while the warning light is coming on. Prompt correction should be necessary.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands