manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 66

INTERIOR SWITCHES

4 - 1 8

CENTER SWITCH PANEL

Seat Warmer Switch

Press the switch to warm the seat in cold weather, and press it again to stop
the operation. The indicator in the switch comes on when in use.

Seat heated wire

Hazard warning
flasher

Hazard Warning Flasher Switch

To turn on the hazard warning flashers, push this
switch. All turn signal lamps will flash simulta-
neously with the hazard warning indicators. Push
this switch again to turn them off.

For driver’s seat

For passenger’s seat

Do not turn on the hazard warning flashers for an ex-
tended period of time when the engine is stopped. The
battery could be discharged.

CAUTION

• If the temperature continues to rise, turn the switch off and have the

system checked by Ssangyong Dealer or Ssangyong Authorized Ser-
vice Operation.

• Do not place anything sharp on the seat. This may cause damages to

the seat heater.

WARNING

• Do not operate the seat heater for a long time when the passenger is

an infant, child, old or handicapped person, person with sensitive skin,
exhausted person or drunk person. They may get burnt.

• Do not put anything on the seat that insulates heat, such as a blanket,

cushion or seat cover.

• When cleaning the seats, do not use organic solvents such as ben-

zene or thinner. The seat surfaces may get deteriorated.

CAUTION

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands