manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 76

INTERIOR SWITCHES

4 - 2 8

BAROMETER AND ALTIMETER

Indication of relative altimeter

Barometer and Altimeter (relative altitude, absolute altitude)

Barometer

It indicates the current atmospheric pressure in range from 720 hpa to 1045 hpa
by 1 hpa.

Altimeter

It indicates the absolute altitude or relative altitude. Press and hold the MODE
button for more than 1 second to switch over the mode between absolute altim-
eter and relative altimeter in direction/atmospheric pressure/altitude mode.

Absolute Altimeter

It indicates the current altitude from sea level (0 m) by every
20 m.

•

Indication range:

 -200 m ~ 2,800 m

•

How to calibrate the absolute altitude

Press UP button: increase by 20 m

Press DOWN button: decrease by 20 m

•

Absolute altitude calibration range

- 200 m ~ 320 m

•

How to erase the calibrated altitude value

Press the UP and DOWN buttons simultaneously for more
than 1 second to cancel the altitude calibration.

Relative Altimeter

• It shows the specific area’s relative altitude based on the

current altitude of the vehicle and shows by every 20 m.

• In relative altimeter mode, reset the relative altitude to 0 m

by using UP or DOWN button. The relative altimeter shows
the destination’s relative altitude after arrival.

Barometer

Altimeter

0 m above the sea level is equivalent to 1013.25 hpa and the altimeter
convert the difference between this pressure and atmospheric pres-
sure to absolute altitude or relative altitude.

NOTE

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands