manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 124

SEATS

7-6

Seatback Reclining Adjustment

Press the button to warm the
seat, and press it again to
stop the operation.

Seat Warmer Switch

PASSENGER’S SEAT

To change the seatback angle,
lean forward slightly and raise the
lever. Then, lean back to the de-
sired angle and release the lever.
After adjusting, make sure the le-
ver is retuned to its original posi-
tion and the seatback is locked.

To move the seat forward or
backward, pull and hold the seat
slide lever up and move the seat
as required. Then, release the le-
ver in desired position.

Seat Slide Adjustment

To raise the head restraint, pull it
up without pressing the release
button. To lower the head restraint,
press the release button   on top
of seatback and push the head re-
straint down.

Seat Under Tray

The seat under tray is located
under the passenger’s seat.
Hold the front of the tray and
pull forwards to use.

Head Restraint Adjustment

Seat Heater

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands