manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 192

CONVENIENCE DEVICES

11-12

REAR CIGARETTE LIGHTER, REAR CUP HOLDER, REAR STORAGE BOX, REAR POWER OUTLET

Cup Holder (Left)

Cup Holder (Right)

Rear Power Outlet
(Right side of fourth row seat)

This power outlet can be found at right
side of body wall when you raise the
fourth row seat. For detailed cautions and
warnings, refer to "Front Power Outlet"
section.

Rear Cigarette Lighter
(Left side of third row seat)

To operate the cigarette lighter, press it in all
the way when the ignition switch is in the “ACC”
or “ON” position. When it becomes heated, it
automatically pops out ready for use.

For detailed cautions and warnings, refer to
"Front Cigarette Lighter" section.

Rear Storage Box (Left side of third row seat)

The rear storage box is provided to store small personal
properties.

When vehicle is in motion, the liquid may spill
out. Spilled liquid can damage the vehicle and
cause burns if it is hot. Do not use cup
holder while vehicle is in motion.

WARNING

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands