Home
/
SSANGYONG
/
RODIUS 2006
/
Owner'S Manual

SSANGYONG RODIUS 2006, Owner'S Manual

Share

Page: 180 / 286

SSANGYONG RODIUS 2006 Owner'S Manual Download Page 180

TURBO CHARGER SYSTEM

10-4

Good maintenance practices should be observed, particularly
regarding air filtration, oil quality and filtration.

These areas are important because of a turbo-charger’s speed
of operation.

Proper operating procedures and preventive maintenance
practices enhance good turbo-service lift and performance.

The contaminated air cleaner can damage the turbocharger
seriously, so frequently check the air cleaner and observe the
replacement intervals.

TURBOCHARGER INSPECTION

The most defectives in turbocharger are turbine blade damages or
compressor bearing sticks due to lack of oil supply, contaminated
engine oil or external materials.

NOTE

Operating the turbocharger system without the intake and exhaust
manifold mounting can result in severe engine damage.

The turbocharger should be operated when every device is nor-
mally installed.

WARNING

«
...
178
179
180
181
182
...
»

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands