manualshive.com logo in svg

SSANGYONG RODIUS 2006, Owner'S Manual

Share
Download
SSANGYONG RODIUS 2006 Owner'S Manual Download Page 170

VENTILATION, HEATING, AIR CONDITIONING AND AIR PURIFICATION SYSTEM

9-14

Mode Switch

By pressing the switch, the air flow mode changes.

When you press this switch in auto air conditioner operation (“AUTO” indicator appears),
the system is changed to manual air conditioner mode (“AUTO” indicator disappears).

Vent

Bi-level

Floor

Defroster and Floor

Rear air conditioner
ON: "R"

Rear air conditioner
OFF

Fan speed control:

1, 2, 3 stage

Rear heater switch

* Rear heater ON

* This function is not available when the rear air condi-

tioner switch is at (    ) position.

Rear air conditioner switch

• Rear air conditioner OFF:

• Fan speed control: 1, 2, 3 stage

• Rear air conditioner ON: “R” position

Summary of Contents for RODIUS 2006































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands